haht.product_family: Ryton, haht.content_type: TDS, cpchem.advancedSearch.section:
TDS - XE3200NA
For more information and technical
assistance contact:
Chevron Phillips Chemical Company LP
P.O. Box 4910
The Woodlands, TX 77387-4910
877.798.6666
Xtel®XE3200NA
Polyphenylene Sulfide Alloys
Xtel® XE3200NA is an un-reinforced high performance, PPS based alloy developed to provide exceptionally high ductility and impact resistance along with good thermal stability.
NOMINAL ENGINEERING PROPERTIES(1) Value Test Method
  Tensile Strength, psi 5000 ASTM D638
  Elongation, % 100 ASTM D638
  Elongation at Yield, % 10 ASTM D638
  Flexural Strength, psi 6000 ASTM D790
  Flexural Modulus, psi 150,000 ASTM D790
  Elastic Modulus, psi 150,000 ASTM D638
  Notched Izod Impact, kJ/m2 35 ISO 180A
  Heat Deflection Temperature, 264 psi,°F 175 ASTM D648
  Heat Deflection Temperature, 66 psi,°F 210 ASTM D648
  Coefficient of Linear Thermal Exp., X 10-6 in/in/°C   ASTM E831
      Axial Direction, -50°C to 50°C 150  
      Axial Direction, 100°C to 200°C 150  
      Transverse Direction, -50°C to 50°C 150  
      Transverse Direction, 100°C to 200°C 150  
  Thermal Conductivity, BTU·in/hr·ft2·°F 1.4  
  Dielectric Strength, V/mil 600 ASTM D149
  Dielectric Constant, 78° F   ASTM D150
      1kHz 3.2  
      1MHz 3.1  
  Dissipation Factor, 78°F    ASTM D150
      1 kHz 0.01   
      1 MHz 0.02   
  Volume Resistivity, ohm·cm 1 x 1014 ASTM D257
  Comparative Tracking Index, V 125(2) UL 746A
  Density, g/cc 1.15 ASTM D792
  Water Absorption, % 0.10 ASTM D570
  Color Natural  
(1) Test specimen molding conditions:  Stock Temperature, 600-650°F; Mold Temperature, 275°F
(2) This product is not currently UL Listed; test results indicate this level of performance
The nominal properties reported herein are typical of the product but do not reflect normal testing variances and therefore should not be used for specification purposes.
Xtel®XE3200NA
Polyphenylene Sulfide Alloys
Xtel® XE3200NA is an un-reinforced high performance, PPS based alloy developed to provide exceptionally high ductility and impact resistance along with good thermal stability.
NOMINAL ENGINEERING PROPERTIES(5) Value Test Method
  Tensile Strength, MPa 30 ISO 527
  Elongation at Break, % 100 ISO 527
  Elongation at Yield, % 10 ISO 527
  Flexural Strength, MPa 40 ISO 178
  Flexural Modulus, MPa 1100 ISO 178
  Elastic Modulus, MPa 1200 ISO 527
  Notched Izod Impact, kJ/m2 35 ISO 180A
  Heat Deflection Temperature, 1.8 MPa,°C 80 ISO 75
  Heat Deflection Temperature, 0.45 MPa,°C 100 ISO 75
  Coefficient of Linear Thermal Exp., X 10-6 in/in/°C   ISO 11359-2
      Axial Direction, -50°C to 50°C 150   
      Axial Direction, 100°C to 200°C 150   
      Transverse Direction, -50°C to 50°C 150   
      Transverse Direction, 100°C to 200°C 150    
  Thermal Conductivity, W/m·K 0.21  
  Dielectric Strength, kV/mm 24 ASTM D149
  Dielectric Constant, 25°C    ASTM D150
      1kHz 3.2   
      1MHz 3.1   
  Dissipation Factor, 25°C    ASTM D150
      1 kHz 0.01   
      1 MHz 0.02   
  Volume Resistivity, ohm·cm 1 x 1014 ASTM D257
  Comparative Tracking Index, V 125(6) UL 746A
  Density, g/cc 1.15 ISO 1183A
  Water Absorption, % 0.10 ASTM D570
  Color Natural  
(5) Test specimen molding conditions:  Stock Temperature, 315-345°C; Mold Temperature, 135°C
(6) This product is not currently UL Listed; test results indicate this level of performance
The nominal properties reported herein are typical of the product but do not reflect normal testing variances and therefore should not be used for specification purposes.
MSDS #CPC00423 Revision Date January, 2008
Before using this product, the user is advised and cautioned to make its own determination and assessment of the safety and suitability of the product for the specific use in question and is further advised against relying on the information contained herein as it may relate to any specific use or application. It is the ultimate responsibility of the user to ensure that the product is suited and the information is applicable to the user's  specific application. Chevron Phillips Chemical Company LP does not make, and expressly disclaims, all warranties, including warranties of merchantability or fitness for a particular purpose, regardless of whether oral or written, express or implied, or allegedly arising from any usage of any trade or from any course of dealing in connection with the use of the information contained herein or the product itself. The user expressly assumes all risk and liability, whether based in contract, tort or otherwise, in connection with the use of the information contained herein or the product itself. Further, information contained herein is given without reference to any intellectual property issues, as well as federal, state or local laws which may be encountered in the use thereof. Such questions should be investigated by the user.
F8FDD8CB17A64B0488295D97054203DA .